805FC Vibration Meter
Innovative sensor design minimizes measurement variations caused by device angle or contact pressure, Fluke Connect compatible
Make go or no-go maintenance decisions with confidence. The Fluke 805FC Vibration Meter is the most reliable vibration screening device available for frontline mechanical troubleshooting teams that need repeatable, severity-scaled readings of overall vibration and bearing condition.
Using the Fluke Connect Mobile App it’s now easier than ever to manage your vibration screening workflow. Integrated machine profile functionality allows you to setup machine profiles using the app and then push them directly to your 805 FC Vibration Meter. Users can then use the list of machine profiles to create work orders, and develop route based maintenance schedules which can be dynamically sent to technicians in field, helping to ensure the proper focus on critical assets. Once a machine is tested, the 805 FC communicates the results directly to the app and associates them with the proper profile and route. This data can easily be shared between teams, so you can make better maintenance decisions.
• Innovative sensor design minimizes measurement variations caused by device angle or contact pressure
• Consistent data quality at both low and high frequency ranges
• Four-level severity scale assesses urgency of problems for overall vibration and bearing condition
• Exportable data via USB
• Trending in Microsoft® Excel using pre-built templates
• Overall vibration measurement (10 Hz - 1,000 Hz) for acceleration, velocity and displacement units of measurement for a wide variety of machines
• Crest Factor+ technology provides reliable bearing assessment using direct sensor tip measurements between 4,000 Hz and 20,000 Hz
• Compare vibration levels with ISO-10816 severity scales and store results to the Fluke Connect Cloud
• Get authorization to take next steps in an instant if machine health is at risk via Fluke Connect® Share-Live™ video call*
• Colored lighting system (green, red) and on-screen comments indicate how much pressure needs to be applied to take measurements
• Temperature measurement with Spot IR Sensor increases diagnostic capabilities
• On-board memory holds and saves up to 3,500 measurements
• External accelerometer support for hard to reach locations
• Flashlight for viewing measurement locations in dark areas
• Large screen with high resolution for easy navigation and viewing
Vibration Meter | ||
Low Frequency Range (Overall Measurement) | 10 Hz - 1,000 Hz | |
High Frequency Range (CF+ Measurement) | 4,000 Hz - 20,000 Hz | |
Severity Levels | Good, Satisfactory, Unsatisfactory, Unacceptable | |
Vibration Limit | 50 g peak (100 g peak-peak) | |
A/D Converter | 16-bit | |
Signal-To-Noise Ratio | 80 dB | |
Sampling Rate | Low Frequency | 20,000 Hz |
High Frequency | 80,000 Hz | |
Real-Time Clock Backup | Coin battery | |
Sensor | |
Sensitivity | 100 mV g +/- 10% |
Measurement Range | 0.01 g - 50 g |
Low Frequency Range (Overall Measurement) | 10 Hz - 1,000 Hz |
High Frequency Range | 4,000 Hz - 20,000 Hz |
Resolution | 0.01 g |
Accuracy (Typical) | At 100 Hz +/- 5% of measured value |
Amplitude Units | |
Acceleration | g, m/s² |
Velocity | in/s, mm/s |
Displacement | mils, mm |
Infrared Thermometer (Temperature Measurement) | |
Range | -20°C - 200°C (-4°F - 392°F) |
Accuracy | +/- 2°C (4°F) |
Focal Length | Fixed, at ~3.8 cm (1.5 in) |
External SensorNote: Fluke supports but does not provide external sensors | |
Frequency Range | 10 Hz - 1,000 Hz |
Bias Voltage (To Supply Power) | 20 V DC - 22 V DC |
Bias Current (To Supply Power) | Maximum 5 mA |
Firmware | |
External Interfaces | USB 2.0 (full speed) communication |
Data Capacity | Database on internal flash memory |
Upgrade | Through USB |
Memory | Up to 3,500 measurements |
Radiated Emission | |
Electrostatic Discharge: burst | Standard EN 61000-4-2 |
Electromagnetic Interference | Standard EN 61000-4-3 |
RE | Standard CISPR 11, Class A |
Environmental | ||
Temperature | Operating | -20°C - 50°C (-4°F - 122°F) |
Storage | -30°C - 80°C (-22°F - 176°F) | |
Operating Humidity | 10% - 95% RH (Non-condensing) | |
Operating/Storage Altitude | Sea level to 3,048 m (10,000 ft) | |
IP Rating | IP54 | |
Vibration Limit | 500 g peak | |
Drop Test | 1 m | |
General Specifications | |
Battery Type | AA (2) Lithium Iron Disulfide |
Battery Life | 250 measurements |
Size (L x W x H) | 25.72 cm x 16.19 cm x 9.84 cm (10.13 in x 6.38 in x 3.875 in) |
Weight | 1.16 kg (2.55 lb) |
Connectors | USB mini-B 7-pin, stereo audio output jack (3.5 mm Audio Plug), external sensor jack (SMB connector) |
| Fluke 805FC Vibration Meter - Data Sheet 1.2 MB |
| Fluke 805FC Vibration Meter - Manual 1.7 MB |
