The Vantageview PD6730 is a plastic, field-mounted flow rate/totalizer that can display flow rate and total from a pulse output flowmeter. Its display has a five digit upper line for rate, a seven alpha-numeric character lower line for total, and comes standard with a backlight. The PD6730 is built in a NEMA 4X and IP65 rated plastic enclosure which can stand up to even the harshest environmental conditions. It can be powered from an included battery or a 24 VDC external power supply. Some features that really make the PD6730 stand out are its automatic unit conversions from flowmeter k-factor units, ability to log up to 1024 data points, and SafeTouch® through-window buttons. These buttons allow the PD6730 to be programmed and operated through the cover window, thus eliminating the need to remove the cover in dirty or wet environments.
• Automatic Rate, Total, and Grand Total Unit Conversions
• On-Board Data Logging
• Modbus Communications RS-485 Option
• All Models Operate from -40 to 75°C
• Two Isolated Open Collector Pulse Outputs, Up to 5 kHz
• Open Collector, NPN, PNP, TTL, Switch Contact, Sine Wave (Coil), Square Wave, Opto-Isolated Inputs
• Plastic NEMA 4X, IP65 Enclosure
• Isolated 4-20 mA Output for Rate, Total, or Grand Total
• Battery, DC, or Output Loop-Powered Models
|Display||Top: Five digits (0 to 99,999), 0.7" (17.8 mm) high, 7-segment, automatic lead zero blanking. Bottom: Seven characters, 0.4" (10.2 mm) high, 14-segment automatic lead zero blanking. Symbols: Total, grand total, battery power/low battery, high & low alarm, password lock, and SafeTouch button sleep mode/disable.|
|Display Assignment||Top Display: Rate or total; Bottom Display: Combinations of rate, total, grand total, units, and custom tag.|
|Backlight||White LED, 10 sec auto-off when battery powered. Backlight deactivated below temperature ≈ -20°C|
|Display Update Rate||Ambient > -20°C: 1 Update/Second. Ambient < -20°C: 1 Update/10 Seconds.
Note: Update is dependent on gate settings.
|Display Orientation||Display may be mounted at 90° increments up to 270° from default orientation|
|Over Range||Display flashes 99,999|
|Programming Method||Four SafeTouch through-window buttons when cover is installed. Four internal push buttons when cover is removed.|
|Recalibration||Calibrated at the factory to read frequency in Hz. No recalibration required.|
|Max/Min Display||Max/Min readings reached by the process are stored until reset by the user or until power to the meter is cycled|
|Password Menu Options||Three programmable password selections can be used for the following: restrict modification of settings, prevent resetting the total or grand total without the password, or permanently lock out the ability to change or reset the grand total or any grand total related settings(making a non-resettable grand total).
Pass: Restricts modifications of programmed settings to require re-entering the password to make changes.
Pass T: Restricts the reset of total to require re-entering the password. Disables the manual mode reset contact.
Pass GT: Restricts the reset of grand total to require re-entering the password. May enable a non-resettable grand total and permanent lockout of grand total-related settings with a specific password.
|Alarm Indication||Flashing display plus HI/LO indicators for rate alarms, SET for total alarms|
|Non-Volatile Memory||All programmed settings and total are stored in nonvolatile memory for a minimum of ten years if power is lost.|
|Power Options||9-30 VDC, 2.2 W max; 4-20 mA Output Powered, 30 VDC max; battery power; 9-30 VDC power with battery backup; 4-20 mA Output Powered with Battery Backup.|
|Battery||3.6 V Primary Lithium (Li-SOCl2), non-rechargeable Model PDABAT36C. Expected service life & recommended replacement interval is dependant on the operating conditions.|