Product Finder

4 zone line end filter kit and expansion kit for the multi-zone refrigerant leak detectors

Lon Works communications package for the multi-zone refrigerant leak detectors

N2 (JCI Metasys) communications package for the multi-zone refrigerant leak detectors

BacNet communications module package for the multi-zone refrigerant leak detectors

Backup power supply for the multi-zone refrigerant leak detectors

Surge protector for the multi- and single-zone refrigerant leak detectors

Variable flow regulator for the multi- and single-zone refrigerant leak detectors

Gas verification kit for for the multi- and single-zone refrigerant leak detectors

Splitter kit for the multi- and single-zone refrigerant leak detectors

Air sample tubing for the multi-zone (HGM-MZ, AGM-MZ) and single-zone (HGM-SZ, AGM-SZ) refrigerant leak detectors

Calibrated replacement sensor assembly for the MVR-300

Extractor tool to remove the sensor module during replacement for the MVR-300

Kits for the MVR-300

Magnetic wand for the MVR-300

Pressure regulator for the MVR-300

Printer paper (5 rolls) for the ECA 450

High temperature probe for the ECA 450

Repair Kit for the Fyrite Classic

Refill kit for the Fyrite Classic

Fyrite fluids for the Fyrite Classic

Pressure hose (6 ft. of 1/8 in. I.D. tubing with female draft connector) for the ECA 450

CO appliance test kit for the Fyrite INSIGHT Plus, Fyrite InTech, and Monoxor Plus

O₂ sensor upgrade kit (from 2 yr. to 3 yr. sensor) for the Fyrite INSIGHT Plus

Pressure tubing kit for the PCA3 and Fyrite INSIGHT Plus

Sample conditioner for the PCA4 and ECA 450

High temperature particulate filter for the PCA4, and ECA 450

Probe with 15 ft. sample tube for the PCA4, and ECA 450

Flue plugs, 5/16 in. (50 pk.) for the PCA3, Fyrite INSIGHT Plus, and Fyrite InTech

Ruggedized high-working ScopeMeter voltage probe set, available in four colours

Probe-sets, 10:1, including hook clips, ground leads with mini alligator clips, ground springs and probe-tip insulation sleeves,...

Voltage Probe, 10:1, with safety-designed shrouded 4 mm testpin, for use with the Fluke 120 Series ScopeMeter

Double insulated voltage probe for Fluke 190 Series ScopeMeters

Double insulated voltage probe for Fluke 190 Series ScopeMeters

Holster case for Fluke meters

Automotive electronics troubleshooting kit for the Fluke 190 Series ScopeMeter

Automotive electronics troubleshooting kit for the Fluke 120 Series ScopeMeter

Replacement sensor probe tip for the Informant 2

Rubber boot to protect the Informant 2

Place these receivers throughout your facility and receive all data automatically to your PC without retrieval from loggers

Module transparently repeats RS485 signals at all standard baud rates from 300 to 115.2K baud

Converter module converts RS232 signal levels to the correct electrical signals required by RS485

Two (2) wire Owl sensor cable, for use when connecting external transducers on the Owl series data loggers

Permanent, rust proof, straight plastic key fob for SmartButton Loggers

Replacement in-line cable enclosure with 48” (1.2 m) coaxial pair cables and BNC connectors

Transducer mounting kit with pair SS mounting brackets, pair pipe clamps for OD up to 30” (750 mm) and 30 ml (1 oz) coupling compound

High temperature sonic coupling compound

In-line integral mount and submersible installation versions featuring patented DryLoc® connectors

Oversized check valves for smooth controlled operation, mash proof vent valve (no needle valve)